Description
Exact Product Name on Official Website
FT07 Photocells. On ERREKA’s official branded material, the model is referred to as FT07 photocells / FT07. (ERREKA Connected Access)
Slug
erreka-ft07-photocell-sensors
Product Description
ERREKA FT07 Photocells are wall-mounted transmitter-receiver safety sensors designed for automatic doors and gate installations. They use an infrared beam to detect obstacles and help prevent collision during opening and closing cycles. The system supports multi-voltage power input, synchronized operation, and adjustable optics up to approximately 210°, making alignment easier during installation. It also allows connection of a mechanical NC or resistive 8k2 safety edge, which is useful where extra protection is required. With IP44 protection, relay output selection, and a maximum beam range up to 30 m, FT07 is a practical solution for residential and commercial gate automation in Abu Dhabi. The optional battery-powered transmitter setup also helps reduce wiring in moving leaf installations. (ERREKA Connected Access)
Key Features and Technical Specifications
- Type: Transmitter-receiver photocell pair
- Mounting style: Wall mounted
- Optical adjustment: Approx. 210° on TX and RX
- Power supply TX: 3-3.6 VDC battery, 12-24 VAC, 12-36 VDC
- Power supply RX: 12-24 VAC, 12-36 VDC
- Synchronization: Selectable, works on AC or DC
- Infrared range: Up to 30 m max, 15 m minimum mode
- Range with batteries: practical reduced range depending on setup
- Relay output: NO or NC selectable
- Safety edge support: Mechanical NC or resistive 8k2
- Wavelength: 940 nm
- Photocell response time: <90 ms
- Safety edge response time: <120 ms
- Operating temperature: -20°C to +60°C
- Protection rating: IP44
- Relay contact capacity: 1A at 24 VDC
- Dimensions: 135 x 50 x 31.5 mm (ERREKA Connected Access)
Main Benefits for the Customer
- Improves gate movement safety through reliable obstacle detection
- Adjustable optics help simplify beam alignment on site
- Multi-voltage operation supports wider automation compatibility
- Optional battery-powered transmitter reduces wiring complexity
- Safety edge signal handling adds another layer of entrance protection (ERREKA Connected Access)
Use Cases
- Sliding gate safety systems
- Swing gate automation projects
- Automatic doors with beam interruption protection
- Moving gate leaf setups needing reduced transmitter wiring
- Entrances using photocell and safety edge integration (ERREKA Connected Access)
Compatibility and Installation Notes
- Compatible with automation systems supporting 12-24 VAC or 12-36 VDC input
- TX can also be powered with 2 x 3.6V lithium AA batteries using the compatible battery solution
- Install TX and RX in accurate alignment for stable beam performance
- Receiver should be protected from direct sunlight for best operation
- Typical installation guidance places photocells below 300 mm from ground and within 200 mm of the gate leaf, depending on site conditions
- Configure jumper settings correctly for range, relay mode, and safety edge type (ERREKA Connected Access)
Packing Includes
| Item |
Detail |
| Transmitter module (TX) |
1 pc |
| Receiver module (RX) |
1 pc |
| Drilling templates |
2 pcs |
| Fixing and adjustment screws |
6 pcs |
| Wall plugs |
6 pcs |
| Rubber sealing washers |
6 pcs |
| Cover fixing screws |
2 pcs |
| Safety edge |
Optional, supplied separately |
| FTBAT battery pack |
Optional, supplied separately |
Suggested Anchor Text
advanced entrance safety solution
Buy Now
Strengthen every automated entrance with precise ERREKA safety detection in Abu Dhabi. Call/WhatsApp: +971 54 482 5472
High-sensitivity infrared photocells, multi-voltage architecture, 210° optical adjustment, relay output selection, 8k2 edge support, and IP44-rated protection.
Total Number
287 words
Reviews
There are no reviews yet.